在卷材防水層中粘結不實的部位，窩有水分和氣體，當其受到太陽照射或人工熱源影響后，體積膨脹，造成鼓泡。 如果僅有一層不明顯的白色小霧，說明保溫層基本干燥，可以準備進行防水層的施工。測試完畢應注意將圓孔補平。采取這種測試方法，可以使施工人員比較準確地掌握保溫層的干燥程度，以便及時安排防水層的施上。測試的時間宜選樣在下午2—3點鐘，此時保溫定溫度高，相對溫差人，測試的結果明顯、準確，對大面積屋面保溫層應多測試幾點，全面綜合其檢測數據，以提高其測試的準確性。
1、直徑100mm以下的中、小鼓泡可用抽氣灌膠法治理，并壓上幾塊磚，幾天后再將磚移去即成。
100mm diameter or less, and small bubbling available plastic irrigation pumping method of governance, and pressed a few bricks, a few days before the bricks removed Serve.
2、直徑100～300mm的鼓泡可先鏟除鼓泡處的保護層，再用刀將鼓泡按斜十字形割開，放出鼓泡內氣體，擦干水分，清除舊膠結料，用噴燈把卷材內部吹干。隨后按順序把舊卷材分片重新粘貼好，再新貼一塊方形卷材（其邊長比開刀范圍100mm），壓入卷材下，最后粘貼覆蓋好卷材，四邊搭接好，并重做保護層。上述分片鋪貼順序是按屋面流水方向先下再左右后上。
Bubbling 100 ~ 300mm diameter may be bubbling at the eradication of the protective layer, and then a knife bubbling by oblique cross cut, release the bubbling gas, dry water, remove the old binder with a blowtorch to roll interior dry. Then in order to re-paste the old membrane fragments good, and then posted a new square coil (which side is larger than the surgery range 100mm), under the pressure of the membrane, and finally paste membrane covering the good, good lap four sides, both as a protective layer. Paving the above sequence is fragmented by roofing direction before you get on the water and then left.
3、直徑更大的鼓泡用割補法治理。先用刀把鼓泡卷材割除，按上一做法進行基層清理，再用噴燈烘烤舊卷材槎口，并分層剝開，除去舊膠結料后，依次粘貼好舊卷材，上鋪一層新卷材（四周與舊卷材搭接不小于100mm），然后貼上舊卷材。再依次粘貼舊卷材，上面覆蓋第二層新卷材，最后粘貼卷材，周邊壓實刮平，重做保護層。
Larger diameter bubbling with cut and fill method of governance. A knife to cut off the first bubble membrane, a practice carried out by the primary clean-up, and then blowtorch baking sheet Croucher old port and layered peel, remove the old binder, and then click Paste good old roll, capped a the new membrane layers (four weeks old sheet lap of not less than 100mm), and then paste the old membrane. Then followed paste the old membrane, covering the top of the second layer of the new membrane, and finally paste membrane surrounding compacted Calibrating, redo protective layer.
